The first manufacturer to guarantee a leak-free pool pump is definitely going to corner the market. Until that happens though, pumps will leak and pool owners will probably utter some choice words as they attempt to locate and troubleshoot the source. Let’s review some of the most common leaks and how to address them.
Suction Side Leaks
On the suction side of the pump, any leaks will be air leaks. This means air is being sucked into the system from some point between the skimmer and the impeller. With this type of leak, you will commonly see air bubbles in the pump strainer basket and at the returns in the pool wall.
You might feel daunted by the task of troubleshooting the entire suction side but there are several likely problem areas to check first:
Pump Strainer Lid
If not completely sealed, the strainer cover will allow air in. With the pump on, slowly pour water over the lid. If that decreases or eliminates air within the basket, you have found at least one leak. You might be able to get by with just cleaning and lubricating the lid o-ring but if it looks worn or misshapen, it is best to replace it. Also be sure to check the lid for any cracks.
Cracked PVC and Valves
Cracks in plumbing connections and valves are common sources of air leaks. To test, you can try pouring water over these also. Even if a valve is intact, it might still need a replacement seal.
Low Water Level
Probably the happiest cause of an air leak; this allows air to enter the skimmer but is easily addressed by adding water to the pool. Also check for a stuck skimmer weir.
Strainer Basket Drain Plug
It’s small but this plug can let air in if the o-ring is bad. Inspect it for wear and tear and replace if needed.
For visuals on troubleshooting suction side leaks, see our How to Identify & Correct Air Leaks guide and video
Pressure Side Leaks
Any leaks on the pressure,or discharge, side of things will be water. Since this part of the system is under pressure, water will be forced out any compromised area. The pressure side is anything located after the pump strainer. Signs of a problem are dripping or spraying at the discharge pipe fittings, water collecting underneath the pump, and reduced pool water level.
The impeller spins on the motor shaft and creates water pressure. If it gets damaged by lodged debris or simply worn from long use, the impeller can become the source of a water leak. You will need to remove the motor from the wet end of the pump in order to inspect and replace the impeller.
Housing O-ring or Gasket
If water is leaking from where the the pump housing and motor meet, check for a worn seal here. Should it need to be replaced, it’s a good idea to replace the diffuser o-ring at the same time.
You can have a poorly sealed fitting on this pipe, or possibly PVC shrunken from heat. If your schedule 40 pipe shrinks, a leak can form. To repair this and prevent it from happening again, try using schedule 80 pipe nipples on the suction and discharge. Schedule 80 is heavier duty and will stand up to heat better.
Cracks can develop in the pump strainer housing. Some try to repair hairline cracks but I have not heard of too many success stories over the years. It might be time to replace the housing, if the pump is fairly new, or consider a whole new pump.
Between the pump motor and impeller is the all-important shaft seal that keeps water out of the motor. A leak here is a common cause of motor failure so it’s crucial to address quickly. Some signs are water coming from behind the seal plate and collecting underneath the pump where the motor and wet end meet. You might also hear some abnormal pump noises; this comes from the bearings as water gets inside the motor.
A common cause of this leak is replacing the motor but failing to replace the shaft seal at the same time. Reusing the old seal is a bad idea, as seals warp over time and will likely not mate properly with the new motor.
The advice here is simple – replace the shaft seal. If a tune-up kit is available for your particular pump make and model, it is the perfect time to also replace o-rings and gaskets while you have the whole pump apart.
If checking all of the above fails to locate and troubleshoot your pool leak, it could be in the underground plumbing. Checking this will depend upon your level of proficiency and how accessible those lines are. As much as I hate to say it to any and all with DIY hearts, it might require the help of a pool professional and a dip into your pool bankroll.
For all your swimming pool pumps contact swimming pool pump dubai or call us at +971 4 252 2966